CyberNinja

In my experience, when I bought a pre-registered C Class a few years ago, the dealership always referred to its original license plate until I specifically requested them to alter the registration to my personalised plate.

Most likely, the issue is in the front control arms, my friend.

Thank you for your kind feedback. I believe winter tires are unnecessary in Spain, namely in the Costa Blanca region. The temperature today is 37 degrees. The temperature yesterday was 39 degrees Celsius, indicating extreme heat. Benijofar has not had snowfall for a period of 85 years.

Indeed, it was one of the concerns I had anticipated. In my last piece, I neglected to note that another distinguishing feature of the E250 Sport variant is its bigger diameter front discs, which are also vented. Indeed, it can be inferred that the callipers on this particular W212 model are bigger compared to those seen on other models. Thank you for the kind comment 👍.

I apologise for not mentioning earlier that one of the additional distinctions on the E250 Sport model is the presence of bigger and vented front discs. Additionally, I have been a longstanding member of this exceptional organisation for some years, predating my ownership of the W212. Prior to my current vehicle, I had a W211 Elegance, specifically a C320, which had impressive acceleration. My first experience with Mercedes-Benz dates back to 2004 when I purchased a C240. Over the years, I had several different discussions on this platform. However, last year I was unable to access my account using my prior login information, which is why I am now using the username "new member".

Greetings, everyone. I own a 2011 E250 Sport (Automatic) that I purchased in 2012 when it had just 9,000 kilometres. This variant is equipped with the AMG body package, wheels, steering wheel, polished pedals, and a few other AMG components. I believe all of these features were included as standard on the Sport model, however I am uncertain. Throughout the years, the automobile has remained mostly dependable, with the exception of a main drive belt failure, a fractured cooling pipe fitting, and a few sensor repairs. When I made the decision to retire in Spain, I took it with me around 5 years ago. Nevertheless, there is one aspect that has always bothered me since I made the purchase, which is the excessively rough ride quality. This may likely be ascribed to the 18-inch wheels equipped with low-profile tires, as well as the somewhat firmer suspension found in the Sport model. I often ponder if I might enhance the quality of the ride by replacing the wheels with 17-inch ones (or maybe 16-inch ones if feasible), appropriately equipped with the corresponding tires. I understand that there may be a little sacrifice in handling, but as I age (now 72), I no longer have the need for high-speed driving and would like a more comfortable ride. Although the automobile is in excellent condition both inside and out, the existing 18" alloy wheels are severely scratched, showing signs of delamination in some areas, and overall seem untidy. I can have the wheels repaired at this location, but the cost is around €100 (£85) each wheel. Additionally, I would have to deal with the inconvenience of not having a vehicle for approximately one week. Additionally, I have the opportunity to get some good pre-owned OEM wheels at a similar cost. Therefore, in conclusion, here is the caveat.... In addition to the factory-installed variations described above, the Sport variant additionally has offset wheels. The front wheels have a width of 8.5J, a diameter of 18 inches, and an offset of ET48. The recommended tire size for the front wheels is 245 x 40 x 18 Y. The rear wheels have a size of 9J x 18 with an offset of ET54. The corresponding tire size is 265 x 35 x 18 Y. The specified offset for the front wheels is between 46 and 50, while for the rear wheels it is between 52 and 56. I would want to know whether it is possible to install 17-inch (or even 16-inch) wheels, ideally without the bigger rear wheels. Would all four wheels have the same width, either 8.5J or 8J? It seems that the majority of other W212 models were equipped with either 16" (E200) or 17" (E220/E250 but not Sport) wheels from the factory. I have some uncertainty about the potential impact of this modification on the specified offset. The only expected changes are that the rear wheels will not protrude as far and may come into contact with the discs or brake cylinders, assuming the front wheels are less than 8.5J in width. Would it be possible to utilise appropriate spacers with the somewhat narrower wheels to mitigate this potential problem? Do any of you knowledgeable individuals have any experience with using smaller wheels? Alternatively, you may provide any comments or advise. I have the option to directly contact MB in Germany, but I have lost confidence in their customer assistance, particularly at the dealer level, due to my experiences over the years. Thank you for reading, and I apologise for the lengthy 'War & Peace' book.

Are you planning to go?

Indeed, there is a slender individual present in the WhatsApp group from which you just exited. 😄

zipmate.exe

It is time to replace the clutch and dual mass flywheel, as mentioned before.

Speak English clearly! I am a Scottish individual who proudly wears a traditional garment known as a kilt.

Yesterday, I visited my nearby Tesco store for a quick trip to buy beer. I parked my vehicle around 20 feet away from another car, which was a white GLB with a licence plate reading '73'. After locking my car, I walked past the other GLB and made a joke to the man who was checking his tyre pressures. "The car is aesthetically pleasing, with an excellent choice of colour and motor." Response: "On what basis do you believe you possess the entitlement and boldness to pass judgement on the vehicle I am currently operating?" "Mutter, Mutter, Mutter" For goodness sake, what is happening to the world!

Are there any tactile controls located on the roof, next to the rearview mirror (RVM)?

Did you turn off the vehicle, remove the key, push the buttons to activate them, and then lock the car shortly afterwards?

The issue has been resolved. The issue was not caused by the injectors, but rather by my ignition key. When the key was turned to the "crank" position, it interrupted the flow of electricity to the ECU at pin 26. I identified the issue when I connected the fuel pump relay and saw that INPA disconnected when I attempted to start the engine for more than 5-6 seconds. Consequently, I discovered that the relay disengaged during the starting process. Thank you for your assistance! I will inspect the injectors at some point in the future. The only reason for not completing the task today was due to my forgetfulness in bringing the appropriate measuring cups.

Understood, I will verify if I can locate any resources for the examination. Is it typical for the pre-supply feed pressure to decrease from 3.8 bar to 1 bar during cranking?

I believe they are satisfactory, but I am uncertain. The donor vehicle originated from Germany, and I myself transported it by backpacking and driving it back to my destination. I never had any issues while the e39 was still in use. I like to recall that the vehicle had around 300,000 km on its odometer. To properly inspect the injectors, it is necessary to have the engine running and measure the return feed from each injector, correct?

Hello. I am experiencing difficulties initiating the ignition of my engine. The engine was suspended on a stand for a considerable period of time until I fitted it. During the first startup, I used a significant amount of initial fuel, which resulted in the engine igniting and running smoothly. Subsequently, it became effortless to start the engine. When rewiring the system once again, as I had previously sketched it temporarily while activating it, I had the same issue of difficulty starting it. Although it started successfully with the assistance of gas, it required gas for every subsequent start. Currently, it is not able to start or ignite. Thus concludes the narrative of the issue, and now we will go to the subsequent aspect. The current issue involves an engine swap in an older Volvo 745, where a stand-alone Engine Control Unit (ECU) has been installed. When using INPA, no "valid" fault code is displayed to indicate the specific problem. However, it is observed that the rail pressure is significantly low. During the initial cranking, the pressure rises to 60 bar, but subsequently drops rapidly to 10 bar. I am now use two pumps to maintain the pressure in the low-pressure line, with one pump located within the fuel tank and the other positioned under the vehicle. The gasoline filter was changed during the installation of the engine. According to INPA, the pre-pressure is 3.81 while the gasoline pumps are functioning. while cranking, the figure declines rapidly. Is this considered normal? Furthermore, I attempted to substitute the o-ring on the fuel pressure regulator. Although it seemed to be in good condition, I decided to replace it while it was detached. However, this replacement did not provide any noticeable changes. Based on my observation, there are no air bubbles present in the fuel line, both before and after starting the engine. I have been contemplating if the rail pressure sensor may be responsible for displaying inaccurate pressure readings, but I am unsure of how to measure it. Is it possible that the boost sensor on the intake might potentially contribute to some of the issues? Sincerely

Ensure that you do not fall victim to any fraudulent activities while dealing with the windscreen EZ.

With the exception of the paint on my vehicle, it is in excellent condition considering its age and mileage. I am not aware of any instances of postponed maintenance, but I would promptly address them if I were made aware of any. Considering my intended use for this vehicle, which involves using it as a daily driver with at least 75% of the mileage being lengthy interstate road trips, it is crucial that I prioritise dependability and avoid any potential concerns. Furthermore, I really regret not opting for complete paint protection film (PPF) at the time of purchasing the vehicle. At that time, I failed to comprehend the significance of the PPF. Now, it seems illogical to get it since they claim it amplifies the damage caused by rock chips. There is a possibility that I may repaint the automobile in the future, however it is unlikely. Within the last 15 days, I have had a meticulous detailing, engaged in 3 instances of self-scrubbing washes, and most recently, availed myself of a high-quality automated wash. During the course of those 15 days, I had travelled a minimum distance of 3,500 kilometres. Travelling and washing inevitably cause paint damage. However, I would rather consistently have a clean automobile, even if it causes some little damage to the paint, as opposed to having a dirty car.

The value provided above is the amount before taxes. Below is the copy of the price received from the Audi dealer today, which I believe also does not include taxes. I will get a quotation for the cost of the brake replacement on Monday, when they are doing the oil change.

My automobile has reached a mileage of over 90,000 and is now undergoing maintenance. One shop provided a quotation of $650 for an oil change, while another dealer offered a quote of $450. Consequently, I chose the dealer with the $450 quote and scheduled an appointment for Monday. They informed me that the final cost would be $296. I believe the individual made an error on the computer, resulting in a fee of $450. I decline to advocate for the amount of 296, since I believe that 450 is a more equitable figure. The price for a windscreen at the dealer is $2850, however I have made a booking with Safelight for $2200. The new PS4 tyres will be available on Monday for a price of $1,450. The cost of purchasing new wiper blades from a dealer is around $200, but on Amazon, they are available for $50 or less. The mechanics will inspect the brakes and advise replacing all four rotors and pads. I will likely get new pads and rear rotors from europarts, which will cost a few thousand dollars more. The number is 2500. The price this week to maintain the R8 in excellent condition amounts to $6,500.

Affirmative, there are seals that are capable of being altered. It should be noted that the manufacturer applied lubricant to the seal on the engine side. I would rotate the intermediate shaft to see whether there is any irregularity in its motion. If the surface is not even, then indeed, it indicates that the seal should be changed. To replace the seal on the gearbox side, it is necessary to dismantle the gearbox in order to remove the shaft and replace the seal.