All Activity
- Past hour
-
Depending on your destination and the discs and pads you choose to use... Until 2012, I did all of my own mining.
-
https://go.skimresources.com/?id=130832X1605580&isjs=1&jv=15.7.1&sref=https%3A%2F%2F
-
https://go.skimresources.com/?id=130832X1605580&isjs=1&jv=15.7.1&sref=https%3A%2F%2F
-
I recently upgraded my bike's front brakes with Brembo Xtra discs and pads. Pads cost £55 and discs £70 apiece. In accordance with the maintenance plan, I spent an extra £19 on Pagid DOT4 from Eurocarparts and four calliper bolts and two disc screws from the main dealer. The calliper bolts could be cleaned and reused; the pistons and boots were in fine shape, and my vehicle has the smaller 300mm discs. My L538 is one of the earlier models without brake pad wear sensors, so when mine finally wore out, I heard a screech. Fluid changes were a breeze since I had a Sealey Pressure Bleeder on hand.
-
In Greece, I replaced all four sets of front brake pads about a year ago, and the original Land Rover ones cost around 170€. However, I noticed that the pads had the Ate logo stamped on them, right below the Land Rover logo, so I bought them directly from an Ate dealer in my area, where they were cheaper. Brambo discs
-
range of prices?
-
https://www.amazon.com/s?ascsubtag=v1-90dea8-30503-f5c1f28262-b&k=Brembo
-
Anticipate a substantial amount! Installing high-performance Brembo or Ate kits would be just as affordable, if not cheaper.
-
How much would it cost to replace the brake pads and discs on a 2012 Evoque? Much obliged.
- Yesterday
-
Sitting on top of the engine, the supercharger pulls the front end away from the workstation for about 20 minutes, making the job much easier.
-
Help! I'm having a hoover hose leak.
keithmerc220 replied to Alex1978's topic in General Discussions
In my experience, disabling the supercharger does not require entering service mode. After removing the intake and intercooler, the PCV clips should be located directly beneath the charger, which emerges from the top of the engine. You won't need service mode for this job because it allows you to access the engine's front end. -
https://go.skimresources.com/?id=130832X1595941&isjs=1&jv=15.7.1&sref=https%3A%2F%2Fwww.mini2.com%2Fthreads%2
-
Required smoke machine or similar device, such as a Mevyvac tool (see below for link).
-
Amazon.co.uk : Google AI
-
Zodazoqa PCV Crankcase Vent Valve for Mini Cooper R50-R53, Heat-Resistant | OEM 4693369AA 11127577568 11127513082 11127829990, Heat Resistant Engine Vent Control Valve Replacement : Amazon.co.uk: Automotive
-
Amazon.co.uk : carb cleaner
-
https://www.amazon.co.uk/s/?search-alias=aps&field-keywords=Mini+Cooper+R53
-
In my 2004 R53, there is a vacuum hose leak. My neighbour is a licensed mechanic, and with his help and some trial and error with carb cleaner and brake clean sprayed on the PCV clips—which I knew were in bad shape from when I serviced the mini supercharger last summer—and Google AI, we have determined that this is probably the issue. I needed a solution for my vehicle's rough idle and lack of power brakes. After spraying carb cleaner into the red PCV clilps using a straw attached to the can, we experienced a brief improvement in idle quality. I need to know if I need to remove the supercharger or put the car in front-end service mode in order to access these clips and replace them with upgraded EFI clamps and tubing. Of course, taking the supercharger unit out would be my first choice if I were looking for a simple solution. If anyone has any information to share about this, I would greatly appreciate it. I would prefer not to waste time by investigating things further. After extensive testing, I am confident in saying that the problem is a vacuum leak and not a power brake booster. I would greatly appreciate your guidance. I am incredibly grateful.
-
there is smoke coming out of the M156 starter motor
DSM10000 replied to Craigbelont's topic in General Discussions
Does anyone here have experience with the rope method? It works on most cars.On multiple occasions, I most assuredly did! Another option, with caution, is to simply use compressed air through a sparkplug hole air line adapter to maintain their height. Do you mean the peculiar curved fork that fit into the plug hole of two-valve Polos? I had a few experiences with those. -
there is smoke coming out of the M156 starter motor
Rashman4u replied to Craigbelont's topic in General Discussions
In my experience working with Volkswagen, we were able to repair the valve stem seals on Polos without disassembling the head. As part of the dealership workshop tooling, VW supplied the necessary kit. -
there is smoke coming out of the M156 starter motor
DSM10000 replied to Craigbelont's topic in General Discussions
No vehicle I've ever seen with worn valve seals didn't produce a noticeable blue puff when started cold. Overnight, oil leaked past the seals, but now it's burning off. -
there is smoke coming out of the M156 starter motor
MrGreedy replied to Craigbelont's topic in General Discussions
http://shop.ebay.co.uk/?_nkw=volvo&mkevt=1&mkcid=1&mkrid=710-53481-19255-0&campid=5338181132&toolid=10001&customid=2518X1570512Xf50d43e5e23354d7478a69cf52e6bd88&subId2=15 -
there is smoke coming out of the M156 starter motor
MrGreedy replied to Craigbelont's topic in General Discussions
Get the car warmed up by taking it for a quick drive. After about five minutes of idling, give it a little tap on the accelerator. If the stem seals are faulty, you should see a cloud of smoke. I performed this on my own Volvo t5. -
Hi there! I just bought a c63 w204, and I noticed that it started smoking after cold or warm starts. I'm pretty sure it doesn't smoke when driving or decelerating, though. I was wondering if it was the PCV or the stem seals, but I read somewhere that the latter doesn't smoke when these engines start up. Any thoughts?
-
It ought to be on the negative terminal, if there is one. Apologies for not mentioning that in my previous comment.