Jump to content

All Activity

This stream auto-updates

  1. Past hour
  2. The Wall Connector can show the firmware version in the Tesla app or through a http command on the same Wi-Fi network, but the Mobile Connector doesn't have any way for consumers to see it. Even in Service Mode, it isn't accessible for this vehicle. I can't say for sure whether it's in Tesla Toolbox, but it might be.
  3. What is the process for checking the firmware on the mobile connector?
  4. It most certainly did, but you must have been distracted during the brief moment it updated.
  5. What a fascinating topic! My 2019 Model X came with a mobile connector, and I also have a non-Wi-Fi wall connector that I use occasionally, about once a month. Using the mobile connector is more of an annual occurrence. No notice of a FirmWare update has ever appeared for either of them.
  6. There is probably some sort of physical or electrical issue if your mobile connector stops charging, and it has nothing to do with the software. Do a quick test run to ensure it's functioning, and if it is, the software shouldn't be a concern.
  7. After nine years of driving Teslas, I can say with confidence that the Mobile Connector software updates themselves. That's something I've never considered before
  8. In my experience, updating a Mobile Connector is not something you can be forced to do. As required, it occurs automatically. After an update, the Mobile Connector resumes charging after a brief interruption. I have only seen two updates to my Mobile Connector in the three and a half years that I have owned a Tesla. However, compared to Mobile Connectors, Wall Connectors are far more complicated and update far more frequently (about once a month on average).
  9. You could try plugging it into a 120 volt outlet and the car every so often to check if it updates, which is something I never really considered.
  10. Tesla Wall Connector | Universal Charger | Type 2 | Up to 22kW | Single Phase and Three Phase | 7.3m Cable included | Indoor/Outdoor : Amazon.co.uk: Automotive
  11. https://www.amazon.com/dp/B0FN9YVHB2?ascsubtag=v1-2a14b2-39968-350f4c7306-d
  12. There has been discussion about the mobile connector receiving updates from the car, and the charging process has halted at that point. Given this, I thought it would be best to start a new thread specifically for this. I was wondering if there was anything you guys are doing to keep the Mobile Connector updated with the latest firmware. For contingency purposes, I keep the mobile connector in my car and the wall connector at home. It would be terrible if it suddenly stopped charging while I was on the go. Are you taking any proactive measures to ensure it remains current? In the eighteen months that I've owned my mobile connector, the only time I used it was when I went to see my uncle, who had sold a Y but had the wall plug installed, and I was there with a fairly depleted battery. 😄
  13. Depending on your destination and the discs and pads you choose to use... Until 2012, I did all of my own mining.
  14. https://go.skimresources.com/?id=130832X1605580&isjs=1&jv=15.7.1&sref=https%3A%2F%2F
  15. https://go.skimresources.com/?id=130832X1605580&isjs=1&jv=15.7.1&sref=https%3A%2F%2F
  16. I recently upgraded my bike's front brakes with Brembo Xtra discs and pads. Pads cost £55 and discs £70 apiece. In accordance with the maintenance plan, I spent an extra £19 on Pagid DOT4 from Eurocarparts and four calliper bolts and two disc screws from the main dealer. The calliper bolts could be cleaned and reused; the pistons and boots were in fine shape, and my vehicle has the smaller 300mm discs. My L538 is one of the earlier models without brake pad wear sensors, so when mine finally wore out, I heard a screech. Fluid changes were a breeze since I had a Sealey Pressure Bleeder on hand.
  17. In Greece, I replaced all four sets of front brake pads about a year ago, and the original Land Rover ones cost around 170€. However, I noticed that the pads had the Ate logo stamped on them, right below the Land Rover logo, so I bought them directly from an Ate dealer in my area, where they were cheaper. Brambo discs
  18. https://www.amazon.com/s?ascsubtag=v1-90dea8-30503-f5c1f28262-b&k=Brembo
  19. Anticipate a substantial amount! Installing high-performance Brembo or Ate kits would be just as affordable, if not cheaper.
  20. Today
  21. How much would it cost to replace the brake pads and discs on a 2012 Evoque? Much obliged.
  22. Yesterday
  23. Sitting on top of the engine, the supercharger pulls the front end away from the workstation for about 20 minutes, making the job much easier.
  24. In my experience, disabling the supercharger does not require entering service mode. After removing the intake and intercooler, the PCV clips should be located directly beneath the charger, which emerges from the top of the engine. You won't need service mode for this job because it allows you to access the engine's front end.
  25. https://go.skimresources.com/?id=130832X1595941&isjs=1&jv=15.7.1&sref=https%3A%2F%2Fwww.mini2.com%2Fthreads%2
  26. Required smoke machine or similar device, such as a Mevyvac tool (see below for link).
  1. Load more activity
×
×
  • Create New...