Jump to content

All Activity

This stream auto-updates

  1. Past hour
  2. I merely reinserted my gauges into my cluster. The tachometer also started reading 500 rpm instead of the 850 I had fine-tuned it to previously, which I found odd. I have never encountered this problem when exchanging cluster components on different vehicles. That's probably the issue, I'm afraid. For what reason could identical components from the same make and model produce different results?
  3. When was the last time you checked the temperature? Stickiness and erratic movement are possible issues.
  4. Since I bought the car, the gauge has fluctuated, but it usually hovers around 90–95. When I turn on the heater, the temperature drops to 80 degrees. In hot weather, it usually stays between 90 and 100 degrees when I climb steep hills, but I've never seen it go above 100 until today. But I painted it, and I noticed the temperature gauge needle flickering a bit while I was driving it earlier, so I'm wondering if the paint and parts swap are making it inaccurate. The temperature of my engine needs to be measured accurately. For the most part, when I turn on my car's heater, the needle stays put. Seeing the needle on these cars' gauges wiggle around so much makes me nervous.
  5. There is some room for error in the temperature sending unit's and the gauge's behaviour due to their respective tolerance windows. The results will vary marginally depending on the components that are swapped out. Since the thermostat opens to 80 degrees Celsius, the typical operating temperature range for the vehicle, assuming all is well, is 80 to 85 degrees Celsius. Assuming everything is in working order (adequate coolant, system capacity to sustain 1.2 bar pressure), operating at temperatures of 100C or higher on a very hot day isn't necessarily bad.
  6. Using a different temperature, fuel, and oil pressure gauge, I've noticed that it runs slightly hotter than my other one. This is because I frankensteined my cluster with another cluster that I bought on eBay for parts. While driving this morning, I noticed that my temperature gauge jumped past the 80 mark, indicating that it has been unusually cold in the mornings here in Pennsylvania. That has never been done before. No amount of July humidity, not even on hills, could get it past that point. So, the fact that it occurs at a constant 25 degrees while travelling at highway speed surprises me. The gauge drops when the heat is turned on. I was on the verge of pulling over on the highway this morning due to concerns that I was going to start overheating. Terrified me to no end. Has this happened to anybody else?
  7. Yesterday
  8. The Wall Connector can show the firmware version in the Tesla app or through a http command on the same Wi-Fi network, but the Mobile Connector doesn't have any way for consumers to see it. Even in Service Mode, it isn't accessible for this vehicle. I can't say for sure whether it's in Tesla Toolbox, but it might be.
  9. What is the process for checking the firmware on the mobile connector?
  10. It most certainly did, but you must have been distracted during the brief moment it updated.
  11. What a fascinating topic! My 2019 Model X came with a mobile connector, and I also have a non-Wi-Fi wall connector that I use occasionally, about once a month. Using the mobile connector is more of an annual occurrence. No notice of a FirmWare update has ever appeared for either of them.
  12. There is probably some sort of physical or electrical issue if your mobile connector stops charging, and it has nothing to do with the software. Do a quick test run to ensure it's functioning, and if it is, the software shouldn't be a concern.
  13. After nine years of driving Teslas, I can say with confidence that the Mobile Connector software updates themselves. That's something I've never considered before
  14. In my experience, updating a Mobile Connector is not something you can be forced to do. As required, it occurs automatically. After an update, the Mobile Connector resumes charging after a brief interruption. I have only seen two updates to my Mobile Connector in the three and a half years that I have owned a Tesla. However, compared to Mobile Connectors, Wall Connectors are far more complicated and update far more frequently (about once a month on average).
  15. You could try plugging it into a 120 volt outlet and the car every so often to check if it updates, which is something I never really considered.
  16. Tesla Wall Connector | Universal Charger | Type 2 | Up to 22kW | Single Phase and Three Phase | 7.3m Cable included | Indoor/Outdoor : Amazon.co.uk: Automotive
  17. https://www.amazon.com/dp/B0FN9YVHB2?ascsubtag=v1-2a14b2-39968-350f4c7306-d
  18. There has been discussion about the mobile connector receiving updates from the car, and the charging process has halted at that point. Given this, I thought it would be best to start a new thread specifically for this. I was wondering if there was anything you guys are doing to keep the Mobile Connector updated with the latest firmware. For contingency purposes, I keep the mobile connector in my car and the wall connector at home. It would be terrible if it suddenly stopped charging while I was on the go. Are you taking any proactive measures to ensure it remains current? In the eighteen months that I've owned my mobile connector, the only time I used it was when I went to see my uncle, who had sold a Y but had the wall plug installed, and I was there with a fairly depleted battery. 😄
  19. Depending on your destination and the discs and pads you choose to use... Until 2012, I did all of my own mining.
  20. https://go.skimresources.com/?id=130832X1605580&isjs=1&jv=15.7.1&sref=https%3A%2F%2F
  21. https://go.skimresources.com/?id=130832X1605580&isjs=1&jv=15.7.1&sref=https%3A%2F%2F
  22. I recently upgraded my bike's front brakes with Brembo Xtra discs and pads. Pads cost £55 and discs £70 apiece. In accordance with the maintenance plan, I spent an extra £19 on Pagid DOT4 from Eurocarparts and four calliper bolts and two disc screws from the main dealer. The calliper bolts could be cleaned and reused; the pistons and boots were in fine shape, and my vehicle has the smaller 300mm discs. My L538 is one of the earlier models without brake pad wear sensors, so when mine finally wore out, I heard a screech. Fluid changes were a breeze since I had a Sealey Pressure Bleeder on hand.
  23. In Greece, I replaced all four sets of front brake pads about a year ago, and the original Land Rover ones cost around 170€. However, I noticed that the pads had the Ate logo stamped on them, right below the Land Rover logo, so I bought them directly from an Ate dealer in my area, where they were cheaper. Brambo discs
  24. https://www.amazon.com/s?ascsubtag=v1-90dea8-30503-f5c1f28262-b&k=Brembo
  25. Anticipate a substantial amount! Installing high-performance Brembo or Ate kits would be just as affordable, if not cheaper.
  26. How much would it cost to replace the brake pads and discs on a 2012 Evoque? Much obliged.
  1. Load more activity
×
×
  • Create New...