ML350_Colin Posted 12 minutes ago Share Posted 12 minutes ago Using a different temperature, fuel, and oil pressure gauge, I've noticed that it runs slightly hotter than my other one. This is because I frankensteined my cluster with another cluster that I bought on eBay for parts. While driving this morning, I noticed that my temperature gauge jumped past the 80 mark, indicating that it has been unusually cold in the mornings here in Pennsylvania. That has never been done before. No amount of July humidity, not even on hills, could get it past that point. So, the fact that it occurs at a constant 25 degrees while travelling at highway speed surprises me. The gauge drops when the heat is turned on. I was on the verge of pulling over on the highway this morning due to concerns that I was going to start overheating. Terrified me to no end. Has this happened to anybody else? Quote Link to comment Share on other sites More sharing options...
AMG33D Posted 11 minutes ago Share Posted 11 minutes ago There is some room for error in the temperature sending unit's and the gauge's behaviour due to their respective tolerance windows. The results will vary marginally depending on the components that are swapped out. Since the thermostat opens to 80 degrees Celsius, the typical operating temperature range for the vehicle, assuming all is well, is 80 to 85 degrees Celsius. Assuming everything is in working order (adequate coolant, system capacity to sustain 1.2 bar pressure), operating at temperatures of 100C or higher on a very hot day isn't necessarily bad. Quote Link to comment Share on other sites More sharing options...
ML350_Colin Posted 11 minutes ago Author Share Posted 11 minutes ago Since I bought the car, the gauge has fluctuated, but it usually hovers around 90–95. When I turn on the heater, the temperature drops to 80 degrees. In hot weather, it usually stays between 90 and 100 degrees when I climb steep hills, but I've never seen it go above 100 until today. But I painted it, and I noticed the temperature gauge needle flickering a bit while I was driving it earlier, so I'm wondering if the paint and parts swap are making it inaccurate. The temperature of my engine needs to be measured accurately. For the most part, when I turn on my car's heater, the needle stays put. Seeing the needle on these cars' gauges wiggle around so much makes me nervous. Quote Link to comment Share on other sites More sharing options...
AMG33D Posted 10 minutes ago Share Posted 10 minutes ago When was the last time you checked the temperature? Stickiness and erratic movement are possible issues. Quote Link to comment Share on other sites More sharing options...
ML350_Colin Posted 9 minutes ago Author Share Posted 9 minutes ago I merely reinserted my gauges into my cluster. The tachometer also started reading 500 rpm instead of the 850 I had fine-tuned it to previously, which I found odd. I have never encountered this problem when exchanging cluster components on different vehicles. That's probably the issue, I'm afraid. For what reason could identical components from the same make and model produce different results? Quote Link to comment Share on other sites More sharing options...
Craigbelont Posted 8 minutes ago Share Posted 8 minutes ago A modern thermocouple is the sole reliable method for determining what's happening. This is about "electronics" made in Germany that are 40 years old and that I don't trust with my life. There was still some wiggle room even when the shit was novel. When you factor in the 40 years of corrosion, those old electronics will go with the flow. Relax; just check it with a meter and make a note of the reading. Assuming you maintain your coolant system, which I have no doubt you will, everything should be fine. Reassuring you with "it's gonna be fine" does nothing but make you more anxious, believe me. I was wondering if anyone here suffers from true obsessive-compulsive disorder? Stuff that keeps my car clean isn't just for me. If that's the case, I'd love to receive a private message from you. I could use some assistance with that. Much obliged. Quote Link to comment Share on other sites More sharing options...
ML350_Colin Posted 8 minutes ago Author Share Posted 8 minutes ago Before I left work, I made sure it was at full temperature by checking an infrared thermometer. Even at the thermostat, I'm getting a reading of 80 degrees, so the gauge must be inaccurate; it reads 95 degrees. Quote Link to comment Share on other sites More sharing options...
Craigbelont Posted 8 minutes ago Share Posted 8 minutes ago And that is all. Get a good night's rest! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.